Slia：创建页面，内容为“== Introduction == Arco can be used as "driver" for Power Inspect in order to use the Error Map of Arco and Power Inspect as Metrology Software. == Settings…”

2018-06-04T13:28:45Z

创建页面，内容为“== Introduction == Arco can be used as "driver" for Power Inspect in order to use the Error Map of Arco and Power Inspect as Metrology Software. == Settings…”

新页面

== Introduction ==
Arco can be used as "driver" for [[Power Inspect]] in order to use the Error Map of Arco and [[Power Inspect]] as Metrology Software.

== Settings of the Communication ==
The communication between the two products it is via serial line, it is therefore important to have 2 serial lines available : 
# from where Arco is sending the information to [[Power Inspect]]
# from where [[Power Inspect]] receives the information.

The 2 lines can be:
# Physical ports: in this case it is necessary o to have a cross-over RS232 cable between the 2 ports.
# Virtual: in this case it is necessary to install 2 virtual ports, This can be achieved by using one of the available products in the market.

== Settings in Arco ==
In Arco the setting in the control panel are: 

*Peripherals - External Link - Select ''"[[Power Inspect]]"'' from the drop down menu. 
Set the speed of communication (Normally 19200) and the port from where Arco will send the data. 
 
[[File:Setting Power Inspect in ARCO 1.PNG]] 
 

*System - Advanced 
Set ''"Output on External link"'' check box to ''"Checked"'' 
 
[[File:Setting Power Inspect in ARCO 2.PNG]] 
 
== Copy of the Driver ==
The Driver that allow the communication shall be copied in the Folder of the Driver of [[Power Inspect]]. 
The destination folder may change from version to version but, up to the date of the edit of this page, the folder in called "Driver" and it is under the "..\Sys\Driver. 
The folder to be open is called "AmmonTeck" and the driver file shall be copied there. 
The driver file is provided by Metrostaff. 

== Settings in Power Inspect ==
From [[Power Inspect]] it is necessary to open the CMM Driver Configuration and select from the list the driver Called ''"AmmonTeckEvents"''.
[[File:Setting Power Inspect in ARCO 3.PNG]] 
Opening the Parameters dialog, it is necessary to set the speed and port number of the one from where [[Power Inspect]] will receive the data. 
[[File:Setting Power Inspect in ARCO 4.PNG]] 

== Running Arco ==
In order to have Arco and [[Power Inspect]] communicating, Arco shall have a "Zero Offset Probe" and it shall run the following program. 
 
<code>S(Pzero)=SNSDEF/PROBE,INDEX,POL,0.0000,0.0000,0.00000000,0.00000000,-1.00000000,0.0000,0 
SNSLCT/S(PZero) 
(go) 
F(GSU_1)=FEAT/GSURF 
MEAS/GSURF,F(GSU_1),10000 
ENDMES 
[[JumpTo|JUMPTO]]/go</code> 
 
The recommended solution is to create a project and then run it with the [[runner]] before having [[Power Inspect|Power Inspect]] launched.

[[it:Configurazione di Arco e Power Inspect per utilizzare la mappa degli errori Arco su Power Inspect]]
[[zh-cn:配置Arco和电源检查为了在电源检查中使用Arco错误地图]]
[[pt:Configurando o Arco e o Power Inspect para usar o mapa de erros do Arco no Power Inspect]]
[[de:Konfigurieren von Arco und Power Inspect, um Arco Error Map bei der Stromüberwachung zu verwenden]]
[[es:Configuración de Arco y Power Inspect para utilizar el mapa de error de Arco en Power Inspect]]
[[en:Configuring Arco and Power Inspect In Order to Use Arco Error Map on Power Inspect]]

配置Arco和电源检查为了在电源检查中使用Arco错误地图 - 版本历史

Slia：创建页面，内容为“== Introduction == Arco can be used as "driver" for Power Inspect in order to use the Error Map of Arco and Power Inspect as Metrology Software. == Settings…”